Reference price :
Contact us
  • Series
    PRC
  • Model
    PRC822S-N/MF
  • Brand / Made in
    CITEL / FRANCE
  • Quarter wave coaxial protector type N
  • Frequency: 800-2200 MHz
  • Max Power: 1500 W
  • Low insertion loss
  • Imax 50 kA
  • Maintenance free
  • Bi-directional
  • IP65
  • Standards compliance: IEC 61643-21 / EN 61643-21 / UL497C / UL497E

PRC series (Quarter Wave Protection)

Quarter Wave DC Blocked Protection is an active band pass filter. It has no active components. Rather the body and corresponding stub are tuned to one quarter of the desired wave length. This allows only specific frequency bands to pass through the unit. Since lightning operates only on a very small spectrum, from a few hundred kHz to a few MHz, it and all other frequency’s are short-circuited to ground.

The filter may be selective (narrow band or wide-band), according to the calculation of various mechanical elements.

The PRC technology can be selected with very narrow band or wide band depending on the application. Surge current withstand is the depending on connector type. Typically, a 7/16 Din connector can handle 100kA 8/20μs while an N-type connector can handle up to 50kA 8/20μs.

AC/DC power injection is not possible with this technology typical application is the protection of radio lines that do not have a source voltage

Main characteristics:

  • Insertion losses < 0.2 dB
  • VSWR < 1.2
  • Broadband and narrowband units available
  • Frequency range:

           + 690-2700 MHz

           + 800-2200 MHz

           + 400-500 MHz

           + 870-950 MHz

           + 1700-1950 MHz

           + 1800-2400 MHz

           + 4800-6000 MHz

  • Best PIM performance: less than 160 dBc with 4.3-10 connector
  • Imax : up to 100 kA (8/20μs)
  • Connectors : 7/16, N, BNC, TNC, 7/8 cable

ELECTRICAL PROPERTIES

  • Max. Load current IL: 10A
  • Max Frequency f: 800-2200MHz
  • Insertion loss: < 0.2dB
  • Max. discharge current Imax: 50 kA
  • Protection level @ In (8/20µs) Up: < 30 V
  • Impulse current 2 x 10/350µs Test - D1 Category Iimp: 25 kA
  • Impedance Z: 50 ohms
  • Max Power P: 1500 W
  • Return loss: > 20 dB
  • VSWR: < 1.2:1

MECHANICAL PROPERTIES

  • Technology: Quarter Wave
  • Connection to Network: Connector N male/female
  • Disconnection indicator: transmission interrupt
  • Mounting: connector
  • Housing material: Brass/Surface plating: Cu Zn Sn
  • Operating temperature: -40/+85°C
  • Protection rating: IP65
  • Outdoor application: yes
  • Failsafe behavior: without
  • Contacts: Bronze/Surface plating: Au or Ag
  • Insulation material: PTFE

STANDARDS

  • Standards compliance: IEC 61643-21 / EN 61643-21 / UL497C / UL497E
  • RohS compliance: yes

INSTALLATION, LOCATION OF THE SPD

The efficiency of coaxial protectors is highly dependent on proper installation, in particular their connection to the earthing network of the installation.
The following installations rules must be strictly observed to ensure the efficiency:

  • Equipotential bonding network: all the bonding conductors of the installation must be interconnected and connected to the installation earthing network.
  • Optimized connection of the protector to the bonding network: to reduce the residual voltages during lightning discharge currents, the connection of the protector to the bonding network must be as short as possible (less than 50 cm) and has a proper cross section (at least 4 mm²).

The «feedthrough mounting» versions perfectly meet all these requirements.
Warning: Carefully remove all paintings or insulating coatings to ensure good contact..

  • Location of the protectors: they should preferably be placed at the entrance of the installation (to limit the penetration of lightning currents) and also near sensitive equipment (to enhance protection).


 

closet

CART

No products in your cart
Báo Giá Sản Phẩm