Reference price :
Contact us
  • Series
    DS98
  • Model
    DS98L-400
  • Brand / Made in
    CITEL / FRANCE
  • Cost effective single-phase surge protector
  • Safety disconnection in-line
  • Double connection in series
  • Common/Differential mode
  • SPD type: 2+3
  • Network: 230V single phase
  • AC system: TN
  • Nominal line voltage Un: 230 Vac
  • Max. AC operating voltage Uc: 275 Vac
  • Max. load current IL: 16 A
  • Max. discharge current Imax: 10 kA
  • Total Maximum discharge current Imax Total: 20 kA
  • Standards compliance: IEC 61643-11 / EN 61643-11 / UL1449 
  • Certification: EAC 
DS98 AC surge protector is used for the "secondary" protection of the single phase networks against the surge voltages created by lightning. It is based on an association between a high energy gas tube and varistors. DS98 is equipped with an internal thermal safety which will disconnect the unit from the AC network in case of end of life. This disconnection will be indicated by the turn on of the red led in the front.
Very compact, the DS98 surge protector must be installed close bythe equipment to protect, downstream a «primary» surge protector ( e.g. DS40). DS98 provides both a common and differential mode protection.
These surge protectors can be classified as Type 2 or Type 3, following test class II or III from IEC 61643-1 standard.
The electrical configuration of the DS98 allows a connection in parallelor series modes. In the last case, the maximum load current is 16 A.

ELECTRICAL PROPERTIES

  • SPD type: 2+3
  • Network: 230V single phase
  • AC system: TN
  • Nominal line voltage Un: 230 Vac
  • Max. AC operating voltage Uc: 275 Vac
  • Max. load current IL: 16 A
  • Temporary Over Voltage (TOV) Charasteristics - 5 sec UT: 335 Vac withstand
  • Temporary Over Voltage (TOV) Charasteristics - 120 mn UT: 440 Vac disconnection
  • Operating current Ic: none
  • Follow current If: None
  • Nominal discharge current In: 5 kA
  • Max. discharge current Imax: 10 kA
  • Total Maximum discharge current Imax Total: 20 kA
  • Withstand on Combinaison waveform IEC 61643-11 Uoc: 10 kV
  • Withstand on overvoltages IEEE C62.41.1: 10 kV
  • Connection mode(s): L/N/PE
  • Protection mode(s): Common/Differential mode
  • Protection level CM/DM Up mc/md: 1.5 kV / 1 kV
  • Admissible short-circuit current Isccr: 10 000 A  

MECHANICAL PROPERTIES

  • Technology: MOV + GSG
  • SPD configuration: Single phase
  • Connection to Network: By screw terminals: 2.5 mm² max
  • Format: Plug-in modular box
  • Mounting: Symmetrical rail 35 mm (EN 60715)
  • Housing material: Thermoplastic UL94 V-0
  • Operating temperature Tu: -40/+85°C
  • Protection rating: IP20
  • Failsafe e behavior: AC network cutt-off
  • Disconnection indicator: Red light on
  • Remote signaling of disconnection: no
  • Dimensions: See diagram

NORMS

  • Standards compliance: IEC 61643-11 / EN 61643-11 / UL1449 
  • Certification: EAC 

DECONNECTOR

  • Thermal disconnector: Internal
  • Installation ground fault breaker: Type S or delayed
  • Fuses: Fuses Type gG - 20 A

INSTALLATION

DS98L-400 Type 2+3 AC surge protector - single phase are connected in series on the AC network and must be equipped with external fuses for short-circuit current protection

  • The total length of series connection wires to AC network must be lower than 0.5 m in order not to increase the protection level (Up) provided by the SPD.
  • Wiring is made by screw connections. On some models, a distribution bus can be used.
  • The protection wire coming from the SPD must be connected to the bonding bar of the electrical panel. Paralleling the protection wire with phases conductors must be avoided.
  • The cross sectional wire must be 6 mm² minimum for Type 2 SPD and 16 mm² for Type 1.
  • Local earthing resistance must be in compliance with the electrical rules.

Further information can be found in IEC 61643-12 standard (selection and application principles for low voltage SPD).

 

 

closet

CART

No products in your cart
Báo Giá Sản Phẩm