Reference price :
Contact us
  • Series
    DSLP
  • Model
    DSLP1-230L
  • Brand / Made in
    CITEL / FRANCE
  • Description: Type 2+3 AC Surge protector for LED lighting system Class 1
  • Standards compliance: EN 61643-11 / IEC 61643-11
  • Certification: CB / EAC
  • Technology: MOV+GSG
  • Network: 220-240 V Single-phase
  • AC system: TT-TN
  • Max. AC operating voltage : 320 Vac
  • Max. load current: 5 A
  • Residual Current : None
  • Max. discharge current : 10 kA
  • Total Maximum discharge current : 20 kA
  • Admissible short-circuit current: 10 000 A
  • Protection rating: IP20

DSLP1-230L

DIN rail AC SURGE PROTECTOR FOR LED LIGHTING SYSTEM CLASS 1

LED street lighting is now widely used for its efficiency, its energy cost savings and its life expectancy. Nevertheless this attractive technology has an important weakness: its sensitivity to transient voltages created by lightning or by power switch operations on AC network.
Due to its scattered and over-exposed location, LED lighting system will face induced surges which will create failure of its power supply, damage LED components or loss of the lighting efficiency. For these reasons, the use of relevant surge protectors located upstream the LED lighting systems is highly recommended.
CITEL offers a full range of surge protectors designed to be installed at different points on the lighting network such as streetlights, the base of poles and street cabinets.
CITEL offers solutions adapted to every type of outdoor LED lighting systems : urban, architectural, tunnels etc…
CITEL proposes a complete range of AC surge protectors specifically designed for the protection of LED lighting systems in the lantern or connection boxes.
DSLP series is installed inside the bottom of the lighting pole: its very compact dimension allows a easy integration with the connection box, on DIN rail. DSLP1 is based on a powerful association of MOV and GDT components, secured by thermal disconnector and disconnection light indicator. The DLPM version offers a mechanical indicator in order to inform about the status of the SPD without voltage supply.

 

DSLP được lắp bảo vệ chống sét cho các cột đèn LED chiếu sáng đường phố
 

 

 

 

 

MLPC1 format and electrical diagram

 

ELECTRICAL PROPERTIES

  • SPD type: 2+3
  • Network: 220-240 V single phase
  • AC system: TT-TN
  • Nominal line voltage Un: 230 - 277 Vac
  • Max. AC operating voltage Uc: 320 Vac
  • Max. load current IL: 10 A
  • Temporary Over Voltage (TOV) Charasteristics - 5 sec UT: 335 Vac withstand
  • Temporary Over Voltage (TOV) Charasteristics - 120 mn UT: 440 Vac disconnection
  • Temporary Over Voltage N/PE (TOV HT) UT: 1200 V/300A/200 ms disconnection
  • Residual Current Ipe: none
  • Nominal discharge current In: 5 kA
  • Max. discharge current Imax: 10 kA
  • Total Maximum discharge current Imax Total: 20 kA
  • Withstand on Combinaison waveform IEC 61643-11 Uoc: 10 kV / 5 kA
  • Withstand on overvoltages IEEE C62.41.1: 10 kV / 10 kA
  • Admissible short-circuit current Isccr: 10 000 A
  • Protection mode(s): Common/Differential mode
  • Protection level @ In (8/20µs) Up: 1.5 kV

MECHANICAL PROPERTIES

  • Technology: MOV + GSG
  • Connection to Network: screw terminal 2.5 mm² max. Earthing conductor 2 mm² - length 60 cm
  • Mounting: Symmetrical rail 35 mm (EN 60715)
  • Housing material: Thermoplastic UL94 V-0
  • Operating temperature Tu: -40/+85°C
  • Protection rating: IP20
  • Failsafe be behavior: Disconnection and AC line cut-off
  • Disconnection indicator: Led green OFF and AC network cut-off
  • Voltage/operating indicator: Green Led ON
  • Dimensions: See diagram

DISCONNECTORS

  • Thermal disconnector: Internal
  • Installation ground fault breaker: Type S or delayed

NORMS

  • Standards compliance: IEC 61643-11 / EN 61643-11
  • Certification: CB / EAC 
closet

CART

No products in your cart
Báo Giá Sản Phẩm