• Series
    DAC1-13VG
  • Model
    DAC1-13VG-20-275
  • Brand / Made in
    CITEL / FRANCE
  • Type 1 + 2 + 3 AC surge protector
  • VG Technology
  • Network: 230 V single-phase
  • In : 20 kA
  • Iimp : 12,5 kA on 10/350µs impulse
  • No leakage current
  • Pluggable module for each phase
  • Remote signaling (option)
  • Optimized to TOV
  • EN 61643-11, IEC 61643-11 certified
  • UL1449 ed.5 compliance

The DAC1-13VG is an extreme duty Type 1+2+3 AC surge protector device designed to protect at the entrance of the electrical installation. This SPD is particularly useful in a high lightning density area where the risk of heavy surge current or even direct strike is high (eg: buildings equipped with lightning rods).

The DAC1-13VG is one-pole SPD and can be used in common mode or common and differential mode.

DAC1-13VG AC surge protectors are designed to be connected in multi-pole configuration to protect single-phase, 3-phase and 3-phase+Neutral AC networks, sometimes associated with a dedicated N/PE SPD.

Electrical Characteristics
  • SPD type (following IEC tests): 1+2+3
  • Network: 230 V single-phase
  • AC system: TN
  • Nominal line voltage Un: 230 Vac
  • Max. AC operating voltage Uc: 275 Vac
  • Temporary Over Voltage (TOV) Charasteristics - 5 sec (Without disconnection) UT: 335 Vac withstand
  • Temporary Over Voltage (TOV) Charasteristics - 120 mn (Without disconnection or with safety disconnection) UT: 440 Vac disconnection
  • Temporary Over Voltage N/PE (TOV HT) (Without disconnection or with safety disconnection) UT: 1200 V/300A/200 ms withstand
  • Residual CurrentLeakage current to Ground Ipe: None
  • Follow current If: None
  • Nominal discharge current (15 x 8/20 µs impulses) In: 20 kA
  • Max. discharge current (max. withstand @ 8/20 µs by pole) Imax: 50 kA
  • Total Maximal discharge current max. total withstand @ 8/20 µs Imax Total: 100 kA
  • Impulse current by pole (max. withstand 10/350µs by pole) Iimp: 12.5 kA
  • Total lightning current(max. total withstand @ 10/350µs) Itotal: 25 kA
  • Withstand on Combination waveform IEC 61643-11 Class III test: 1.2/50µs - 8/20µs Uoc: 6 kV
  • Specific energy by pole max. withstand 10/350 µs W/R: 40 kJ/ohm
  • Connection mode(s): L/PE and N/PE
  • Protection level L/PE @ In (8/20µs) Up L/PE: 1.5 kV
  • Protection level N/PE @ In (8/20µs) Up N/PE: 1.5 kV
  • Residual voltage L/PE at 5 kA @ 5 kA (8/20µs) Up-5kA: 0.7 kV
  • Protection level N/PE at 5 kA @ 5 kA (8/20µs) Up-5kA: 0.7 kV
  • Admissible short-circuit current Isccr: 50 000 A
Mechanical Characteristics
  • Technology: VG Technology (MOV+GSG)
  • SPD configuration: single-phase (L+N)
  • Connection to Network: By screw terminals: 2.5-25 mm² (35 mm² rigid)
  • Format: Plug-in modular box
  • Mounting: Symmetrical rail 35 mm (EN 60715)
  • Housing material: Thermoplastic UL94 V-0
  • Operating temperature Tu: -40/+85°C
  • Protection rating: IP20
  • Failsafe mode: Disconnection from AC network
  • Disconnection indicator: 1 mechanical indicator by pole - red/ Green
  • Spare module(s) MDAC1-13VG-275
  • Remote signaling of disconnection:  option DAC1-13VGS-20-275 : output on changeover contact
  • Dimensions: 2TE (EN43880)
Disconnectors
  • Thermal disconnector: Internal
  • Installation ground fault breaker: Type S or delayed
  • Fuses: 125 A min. - 315 A max. - Fuses Type gG
Standards
  • Standards compliance: IEC 61643-11 / EN 61643-11 / UL1449 4ed.
  • Certification: KEMA / EAC

INSTALLATION

DAC1-13VG-20-275 Type 1+2+3 AC surge protector - single-phase are connected in parallel on the AC network and must be equipped with external fuses for short-circuit current protection

  • The total length of parallel connection wires to AC network must be lower than 0.5 m in order not to increase the protection level (Up) provided by the SPD.
  • Wiring is made by screw connections. On some models, a distribution bus can be used.
  • The protection wire coming from the SPD must be connected to the bonding bar of the electrical panel. Paralleling the protection wire with phases conductors must be avoided.
  • The cross sectional wire must be 6 mm² minimum for Type 2 SPD and 16 mm² for Type 1.
  • Local earthing resistance must be in compliance with the electrical rules.

Further information can be found in IEC 61643-12 standard (selection and application principles for low voltage SPD).

closet

CART

No products in your cart
Báo Giá Sản Phẩm