ATLINE12 2-pair overvoltage protector for 12V data line (2kA/8kA)

Reference price :

Select a product to request a quote

ATLINE12 2-pair overvoltage protector for 12V data line (2kA/8kA)

Name: ATLINE12 2-pair overvoltage protector for 12V data line (2kA/8kA)
Brand: AT
SKU: ATLINE12
Availability: InStock
Rating: 5 (1 reviews)

Series

ATLINE
Model

ATLINE12
Brand / Made in

AT / SPAIN

Nominal voltage Un: 12 Vdc
Maximum continuous operating voltage Uc: 15 Vac/dc
Protection level for 8/20μs wave (at In) Up: 66 V
Response time tr: 10 ns
Nominal discharge current per line C2 4 kV (1.2/50μs) / 2 kA (8/20μs) In: 2 kA
Total nominal discharge current per line C2 4 kV (1.2/50μs) / 2 kA (8/20μs) In: 8 kA
Nominal current In: 360 mA
Certificated tests according to EN IEC 61643-21

ATLINE series

Protection for the digital and analogical equipment connected to these lines (computers, PLCs, load cells etc.). Wide variety of protectors for different working voltages.
Connects up to 2 pairs of lines that are very small in size. Both common and differential protection recommended for this type of line.
With removable modules for replacement in the event of a breakdown or fault. The power supply is not interrupted when replacing the module.
It has a radiofrequency receptor in order to carry out maintenance using only an emitter kit.
Earthing system is introduced through a metal sheet opposite to the fixing on the DIN rail.
Discharge takes place in an internal encapsulated element with no external flash.
Low residual voltage for all operating voltages.
Quick response.
Mechanical connection of conductors using screws, in order to absorb a higher amount of overvoltage.
In normal conditions, it remains inactive without affecting line operation or producing any leakages.
ATLINE series protectors have been tested in official, independent laboratories obtaining their characteristics according to applicable standards.

ATLINE12 is a version for DC lines with Un = 12VDC. C2 Test (2kA/4kV). Up = 66 V

ATLINE Diagram (mm) & SCHEMATICS

Product specifications

Product specifications
product manual
Download file

ELECTRICAL

Nominal voltage Un: 12 Vdc
Maximum continuous operating voltage Uc: 15 Vac/dc
Protection level for 8/20μs wave (at In) Up: 66 V
Level protection for 1.2/50μs wave: 66 V
Response time tr: 10 ns
Nominal discharge current per line C2 4 kV (1.2/50μs) / 2 kA (8/20μs) In: 2 kA
Total nominal discharge current per line C2 4 kV (1.2/50μs) / 2 kA (8/20μs) In: 8 kA
Nominal current In: 360 mA
Series resistance Rs: 15 Ω

DIMENSIONS

Length 13.5 mm x Height 96 mm x Width 80 mm
Weight: 80 gr
Number of DIN modules (DIN 43880): 3/4

ENVIRONMENTAL

Working temperature: -40 to +70 °C
Protector location: Indoor
Enclosure protection: IP20

CONSTRUCTION

Fixing: DIN Rail
Enclosure material: Polyamide
Insulation resistance: > 10^14 Ω
Self-extinguishing enclosure: V-0 Type according to EN IEC 60707 (UL94)
Type of connection: Series (two ports)
Nr. of poles: 4
Warning: visual warning than works when RF SPD TESTER (AT-3501) is activated. Green light blinking: Correct. Off: Replace

CONNECTION

Maximum single-stranded section: 4 mm2
Screw: Philips, PH1

TESTS AND CERTIFICATIONS

Certificated tests according to EN IEC 61643-21
Relevant standards: NF C 17102, UNE 21186, EN IEC 62305
Products compliant with EC requirements

Installation

Protectors should preferably be installed as close to the equipment as possible.
One communication cable or data line may contain several wires. Each ATLINE can protect up to four of these wires in series.
The recommended installation procedure is the following:

1 - Cut the data cable.
2 - Insert the cable ends into the connectors. Carefully check that the input and output connections are correctly placed.
3 - Connect the DIN rail to the earth terminal, since the overvoltage will be diverted to this element.

Safety & Maintenance

Earthing system is introduced through a metal sheet opposite to the fixing on the DIN rail.
Connection to earth is a must. Earthing in the whole installation must be bonded either directly or by a spark gap and resistance should be lower than 10 Ω.