ATLAN 24 patch panel surge protector for 24 ports 1Gb Ethernet

Reference price :

Select a product to request a quote

ATLAN 24 patch panel surge protector for 24 ports 1Gb Ethernet

Name: ATLAN 24 patch panel surge protector for 24 ports 1Gb Ethernet
Brand: AT
SKU: AT-2208
Availability: InStock
Rating: 5 (1 reviews)

Series

ATLAN
Model

AT-2208
Brand / Made in

AT / SPAIN

Maximum transfer speed: 1000 Mbit/s
Nominal voltage (Un): 5 VDC
Nominal discharge current per line C2 (In (C2)): 2 kA
Type of connection: Series (two ports)
Nr. of pairs protected: 24 x 4 pairs
Certificated tests according to: UNE-EN IEC 61643-21

ATLAN 24 - Surge protection forcomputer networks. 1 GBit/s. RJ45 input/output connectors. C2 Test (2kA/4KV). Up = 100V. Includes 24 cables with RJ45 connectors, 0,5 m long and 19'' rack.

ATLAN protectors are especially designed to prevent failures in data transfer between equipment within the same network. They protect the electronic circuit inputs of the network cards against damage due to transient currents.

ATLAN 24 is an SPD for 24 lines protection with four pairs protected per line. This is done using a printed circuit board with RJ45 input/output connectors, able to withstand current up to 2 kA for each line and with a transfer speed of Gbits/s.
It is especially designed to be inserted into a rack and protect computer network distribution cabinets. Due to its high transfer speed, it is suitable for networks transferring a large amount of data (servers, workstations, graphic stations etc). Includes 50 cm output cables with RJ45 connector.

Tested in official and independent laboratories, obtaining their characteristics according to relevant standards (shown in the table).

Product specifications

Product specifications
product manual
Download file

DATASHEET

Reference: AT-2208
Maximum transfer speed: 1000 Mbit/s
Nominal voltage (Un): 5 VDC
Maximum continuous operating voltage (Uc): 6 VDC
Nominal discharge current per line C2 (In (C2)): 2 kA
Protection level at In(8/20 µs wave) (Up(In)): 100 V
Maximum operating current (IL): 300 mA
Series resistance (Rs): 11 Ω
Response time (tr): < 10 ns
Working temperature: -40 °C to +70 °C
Protector location: Indoor
Type of connection: Series (two ports)
Nr. of pairs protected: 24 x 4 pairs
Dimensions: 483 x 150 x 44 mm
Enclosure material: Steel
Enclosure protection: IP20
Input / output connector: RJ45 / RJ45 shielded
Earthing system: Screw M5

TESTS AND CERTIFICATIONS

Certificated tests according to: UNE-EN IEC 61643-21
Relevant standards: UNE 21186, NF C 17-102, IEC 62305
Products compliant with EC requirements

INSTALLATION

Protection should be installed as close as possible to the equipment. In this particular case, we are talking about switches and hubs.

If there are two pieces of equipment located in separate buildings but linked together, the protection must be installed on both sides of the line.
The recommended procedure for installation is the following:

Screw the protectors onto the 19 inch rack for computer network distribution.
Run the network distribution lines from the hub or switch to the protector.

SAFETY AND MAINTENANCE

Connection to earth is a must. Earthing in the whole installation must be bonded either directly or by a spark gap and resistance should be lower than 10Ω.

If the indications on this datasheet are not fulfilled during use or installation of the protectors, the protection provided by this device could be compromised.