DS500E-400 Type 1+2 AC surge protector - 1 pole

Reference price :

Select a product to request a quote

DS500E-400 Type 1+2 AC surge protector - 1 pole

Name: DS500E-400 Type 1+2 AC surge protector - 1 pole
Brand: CITEL
SKU: DS500E-400
Availability: InStock
Rating: 5 (1 reviews)

Series

DS500E
Model

DS500E-400
Brand / Made in

CITEL / FRANCE

Description: Type 1+2 AC surge protector - 1-pole
Standards compliance: IEC 61643-11 / EN 61643-11
Certification: EAC
Technology: MOV
Remote signaling of disconnection: Output on changeover contact
Network: 230/400 V
Max. AC operating voltage: 440 Vac
Residual Current: < 3 mA
Max. discharge current: 200 kA
Impulse current by pole: 50 kA
Protection level: 2.2 kV
Admissible short-circuit current: 50 000 A

The DS500E range of surge protectors are Type 1 + 2, very high power, they are intended to be installed at the entry of the Low Voltage installation. They are used to protect single-phase, three-phase or three-phase + Neutral networks in common mode or in common and differential mode. The 'Multi-Varistor' technology used allows the best possible behavior for the LV network (no follow-on current). The DS500E range is installed on a DIN Rail and has a double connection for the active conductor, which allows an optimized connection to the network.

Product specifications

Product specifications
product manual
Download file

Electrical Characteristics

SPD type (following IEC tests): 1+2
Network: 230/400 V
Max. AC operating voltage Uc: 440 Vac
Max. load current(if series connection) IL: 100 A
Temporary Over Voltage (TOV) Charasteristics - 5 sec (Without disconnection) UT: 580 Vac withstand
Temporary Over Voltage (TOV) Charasteristics - 120 mn (Without disconnection or with safety disconnection) UT: 770 Vac disconnection
Operating current Continious current at Uc Ic: < 3 mA
Follow current If: None
Nominal discharge current (15 x 8/20 µs impulses) In: 50 kA
Max. discharge current (max. withstand @ 8/20 µs by pole) Imax: 200 kA
Impulse current by pole (max. withstand 10/350µs by pole) Iimp: 50 kA
Specific energy by pole (max. withstand 10/350 µs) W/R: 625 kJ/ohm
Connection mode(s): L/N and L/PE
Protection level @ In (8/20µs)) Up: 2.2 kV
Admissible short-circuit current Isccr: 50 000 A

Mechanical Characteristics

Technology: MOV
Connection to Network: By screw terminals: 6-35mm² / by bus
Format: 1-pole modular box assembled
Mounting: Symmetrical rail 35 mm (EN 60715)
Housing material: Thermoplastic UL94 V-0
Operating temperature: -40/+85°C
Protection rating: IP20
Failsafe mode: Disconnection from AC network
Disconnection indicator: 1 mechanical indicator
Remote signaling of disconnection: Output on changeover contact
Dimensions: See diagram

Disconnectors

Thermal disconnector: Internal
Installation ground fault breaker: Type S or delayed
Fuses: Fuses Type gG - 500 A

Standards

Standards compliance: IEC 61643-11 / EN 61643-11
Certification: EAC

INSTALLATION

DS500E-400 Type 1+2 AC surge protector - 1 pole is connected in parallel on the AC network and must be equipped with external fuses for short-circuit current protection

The total length of parallel connection wires to AC network must be lower than 0.5 m in order not to increase the protection level (Up) provided by the SPD.
Wiring is made by screw connections. On some models, a distribution bus can be used.
The protection wire coming from the SPD must be connected to the bonding bar of the electrical panel. Paralleling the protection wire with phases conductors must be avoided.
The cross sectional wire must be 6 mm² minimum for Type 2 SPD and 16 mm² for Type 1.
Local earthing resistance must be in compliance with the electrical rules.

Further information can be found in IEC 61643-12 standard (selection and application principles for low voltage SPD).

Combine two DS500E-400 to get DS502E-400 used for AC 230 V single phase network, IT system
Combine three DS500E-400 to get DS503E-400 used for AC 230/400V 3-phase network, IT system
Combine four DS500E-400 to get DS504E-400 used for AC 230/400V 3-phase+N network, IT system