Tiếng Việt|English
Hotline: +84 89 88 99 578
ThyAn Lightning and Surge Protection
ATVOLT P5 DC Surge Protector 5Vdc

ATVOLT P5 DC Surge Protector 5Vdc

Model: AT-8590

Origin: AT3W / Spain

Download Catalogue: (English)

Add to cart:

ATVOLT P SPDs allows the protection of the same equipments as ATVOLT series but since these are installed in parallel, they have the characteristic of having no limitation for current consumption. Each SPD protects a pair of wires. Several protection stages are internally coordinated. ATVOLT P Series contains a wide range of voltages. They are mainly used for DC supply lines of tens of volts.
Tested and certified as Type 2 according to regulations EN 61643-11 and GUIDE-BT-23 from REBT. Suitable for Categories I, II, III and IV equipment according to ITC-BT-23 from REBT Recommended protection in both common and differential mode.

  • Wide variety of SPDs for different working voltages.
  • It remains inactive in normal conditions, without affecting the normal working of the line and without leakage.
  • Discharge takes place in an internal encapsulated element, with no external flash.
  • Mechanic connection for conductors through screws, which allows absorbing a highest amount of voltage.
  • Possibility of connection to a M5 fork terminal
  • Suitable for TT, TN-C and TN-S systems.
  • Coordinable with other SPDs such as ATSHOCK and ATCOVER.
  • Quick response
  • ATVOLT P SPDs have been tested in official, independent laboratories, obtaining their characteristics according to relevant standards (related in the table).

Installation ATVOLT P 

ATVOLT P Surge Protective Devices are to be installed in parallel connected to positive and negative line. ATVOLT P can be installed as single protection or in combination with other protectors that withstand higher discharge currents. In this case, it is necessary that both are separated by at least 10 meter cable or, if this is not possible, by a decoupling inductor ATLINK, in order to achieve a correct coordination between them. The lower terminal must be connected to the Earth Termination System, where the surge associated current must be derived. ATVOLT P SPDs should be installed preferably as close to the equipment as possible

Technical Datasheet of ATVOLT P: 

 Reference  ATVOLT P5
AT-8590
 ATVOLT P12
AT-8514
 ATVOLT P24
AT-8526
 ATVOLT P48
AT-8549
 Protection categories according to REBT:     I, II, III, IV
 Type of tests according to EN 61643-11: Type 2+3
 Nominal voltage:Un  5VDC  12VDC  24VDC  48VDC
 Maximum working voltage: Uc  7VDC  15VDC  31VDC  65VDC
 Nominal discharge current (wave 8/20μs): In     10kA
 Maximum discharge current (8/20μs wave):Imax      20kA
 Combined wave tension: Uoc     6kV
 Protection level at In (8/20μs wave): Up(In) 500V 530V 630V 730V
 Response timetr     <25ns
 Working temperature     -40oC to +70oC
 SPD location     Indoor
 Type of connection:     Parallel (one port)
 Number of poles     2
 Dimensions:     36 x 90 x 80mm (2 mod. DIN43888)
 Fixing:     DIN rail
 Enclosure material:     Polyamide
 Insulation resistance     >1014
 Autoextinguish enclosure     V-0 Type according to UNE-EN 60707 (UL94)
 Connections    Min/Max section multi-stranded: 4 / 35 mm² (11/2 AWG)
Min/Max section single-stranded: 1 / 35 mm² (17/2 AWG)
 Certificated tests according to: IEC 61643-1, EN 61643-11
 Complies with requirements of: UL 1449
 Relevant standards: UNE 21186, NFC 17102, IEC 62305 
AT3W DC Surge Protectors
Surge Protection for BTS

Surge Protection - Industrial sites

Video tổng quan về Giải pháp Chống sét Lan truyền cho Nhà máy

SPD Installation and Rules

Choosing Surge Protectors

Partners
  • ALLTEC CORPORATION
  • APLICACIONES TECNOLÓGICAS
  • CITEL 2cp
  • Chauvin-Arnoux Group
  • Cylix Corporation